| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Density/Specific Gravity |
*** g/cm³
| ISO 1183 | |
Melt Volume Flow Rate(MVR) | | | |
330°C/2.16kg |
*** cm³/10 min | ISO 1133 | |
Melt Mass Flow Rate(MFR) | | | |
330°C/2.16 kg |
*** g/10 min | ISO 1133 | |
Mold Shrinkage | | | |
Flow |
*** % | ISO 294-4 | 60x60x2 mm |
Across Flow |
*** % | ISO 294-4 | 60x60x2 mm |
Water Absorption |
*** %
| ISO 62 | Equilibrium, 23°C, 50% RH |
Water Absorption |
*** %
| ISO 62 | Saturation, 23°C |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Modulus |
*** Mpa
| ISO 527-1/-2 | 1 mm/min |
Tensile Strength | | | |
Yield |
*** Mpa | ISO 527-1/-2 | 50 mm/min |
Tensile Elongation | | | |
Yield |
*** % | ISO 527-1/-2 | 50 mm/min |
Nominal Tensile Strain at Break |
*** % | ISO 527-1/-2 | 50 mm/min |
Flexural Strength | | | |
- |
*** Mpa | ISO 178 | 2 mm/min |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Charpy Unnotched Impact Strengh | | | |
-30℃ (-22℉) |
*** kJ/m² | ISO 179/1eU | |
23℃ (73℉) |
*** kJ/m² | ISO 179/1eU | |
| Hardness | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Ball Indentation Hardness |
*** Mpa
| ISO 2039-1 | |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | | | |
0.45 Mpa (66 psi)（4.6kg/cm²） |
*** °C | ISO 75-1/-2 | |
1.8 Mpa (264 psi)（18.6kg/cm²） |
*** °C | ISO 75-1/-2 | |
Vicat Softening Temperature(VST) |
*** °C
| ISO 306 | 50 N; 120 °C/h |
Relative Temperature Index(RTI), Imp | | | |
- |
*** °C | UL 746B | |
Relative Temperature Index(RTI), Elec | | | |
- |
*** °C | UL 746B | |
Relative Temperature Index(RTI), Str | | | |
- |
*** °C | UL 746B | |
Coefficient of Linear Thermal Expansion | | | |
Flow |
*** E-6/K | ISO 11359-1/-2 | 23 to 55 °C |
Across Flow |
*** E-6/K | ISO 11359-1/-2 | 23 to 55 °C |
| Flammability | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Flame Rating | | | |
HB |
*** mm | UL94 | |
HB |
*** mm | UL94 | |
Oxygen Index |
*** %
| ISO 4589 | Method A |
Glow Wire Flammability Index(GWFI) | | | |
- |
*** °C | IEC 60695-2-12 | |
| Electrical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Volume Resistivity |
*** Ohm-m
| IEC 60093 | |
Surface Resistivity |
*** Ohm
| IEC 60093 | |
Dielectric Constant(Permittivity) | | | |
100Hz |
*** - | IEC 60250 | |
1MHz |
*** - | IEC 60250 | |
Dissipation Factor | | | |
100Hz |
*** E-4 | IEC 60250 | |
1MHz |
*** E-4 | IEC 60250 | |
Comparative Tracking Index (CTI) | | | |
Solution A |
*** V | IEC 60112 | |
Solution B |
*** V | IEC 60112 | |
Dielectric Strength |
*** kV/mm
| IEC 60243-1 | |
Electrolytical Corrosion |
*** -
| IEC 60426 | |
| Optical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Light Transmission |
*** %
| ISO 13468-2 | 1 mm |
Refractive Index |
*** -
| ISO 489 | Procedure A |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
