MAGNUM™ 342EZ is a standard heat ABS. It is a reliable and cost effective solution for general covered interior automotive applications. MAGNUM™ 342EZ has high flow characteristics supporting part design freedom.
Benefits:
Lot to lot consistency allowing for optimal machine parameters settings from the start
Low VOC allowing a better interior air quality facing increasing regulatory and OEMs constraints.
Heat stability during wide range of processing temperatures: enhanced part design freedom
Applications:
General purpose covered interior automotive applications
Mid-consoles
Door liners
Seat trims
| Original Document | Technical Datasheet-ASTM(English) | |||
| Features | Heat ResistanceHeat StabilizedLow EmissionHigh Flow | |||
| Applications | Automotive Console BoxAutomotive Interior TrimsAutomotive ConsolesAutomotive Interior Parts | |||
| Automotive Specs | FORD WSS-M4D483-C1FCA (Fiat Chrysler Automobiles) MS-DB 200-CPN508FCA (Fiat Chrysler Automobiles) MS-DB 200-CPN3457FORD WSS-M4D827-A3GM(General Motors) GMW15572P-ABS-T1Toyota TSM 5512G-2AGreat Wall MP03-01 | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ASTM D792 | |
Melt Mass Flow Rate(MFR) | |||
230°C/3.8 kg | *** g/10 min | ASTM D 1238 | |
Mold Shrinkage | |||
Flow | ***~*** % | ASTM D955 | |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Modulus | *** Mpa | ASTM D638 | 3.20 mm,Injection Molded |
Tensile Strength | |||
Yield | *** Mpa | ASTM D638 | 3.20 mm,Injection Molded |
Tensile Elongation | |||
Yield | *** % | ASTM D638 | 3.20 mm,Injection Molded |
Flexural Modulus | *** Mpa | ASTM D790 | 3.20 mm,Injection Molded |
Flexural Strength | |||
- | *** Mpa | ASTM D790 | 3.20 mm,Injection Molded |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Izod Notched Impact Strengh | |||
-18℃ (0℉) | *** J/m | ASTM D 256 | 3.20 mm,Injection Molded |
23℃ (73℉) | *** J/m | ASTM D256 | 3.20 mm,Injection Molded |
Instrumented Impact Energy | |||
23℃ (73℉)peak | *** J | ASTM D3763 | 3.20 mm,Injection Molded |
23℃ (73℉)Total Energy | *** J | ASTM D3763 | 3.20 mm,Injection Molded |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | |||
0.45 Mpa (66 psi)（4.6kg/cm²） | *** °C | ASTM D648 | Unannealed |
1.8 Mpa (264 psi)（18.6kg/cm²） | *** °C | ASTM D648 | Unannealed |
Vicat Softening Temperature(VST) | *** °C | ASTM D1525 | Rate B (120°C/h), Loading 1 (10 N) |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
