Udel® P-1700 polysulfone (PSU) is a tough, rigid, high-strength thermoplastics suitable for continuous use up to 300°F (149°C). It is resistant to oxidation and hydrolysis and withstand prolonged exposure to high temperatures and repeated sterilization. Udel® P-1700 polysulfone is highly resistant to mineral acids, alkali and salt solutions. Resistance to detergents and hydrocarbon oils is good, but the resin may be attacked by polar solvents such as ketones, chlorinated hydrocarbons and aromatic hydrocarbons.
These resins are also highly resistant to degradation by gamma or electron beam radiation. Electrical properties of Udel® P-1700 polysulfones are stable over a wide temperature range and after immersion in water or exposure to high humidity.
The resins comply with FDA 21 CFR 177.1655 and may be used in articles intended for repeated use in contact with foods. Additionally, they are approved by the NSF, by the Department of Agriculture for contact with meat and poultry and by the 3-A Sanitary Standards of the Dairy Association.
Transparent: Udel® P-1700 CL 2611 CMP
Transparent: Udel® P-1700 NT 06
Transparent: Udel® P-1700 NT 11
Opaque Black : Udel® P-1700 BK 937
Opaque White: Udel® P-1700 WH 6417
Opaque White: Udel® P-1700 WH 7407
Opaque Gray: Udel® P-1700 GY 8057
| Original Document | Technical Datasheet(English) | |||
| Features | Good ToughnessHeat StabilizedGood SurfaceDimensional StabilityFood ContactBiocompatibleE-beam SterilizableGamma ResistanceEtO sterilizableSteam ResistantChemical ResistanceHydrolysis ResistanceAcid ResistancAlkali resistanceAlcohol ResistantDetergent resistantHydrocarbon Resistant | |||
| Appearance | Pellets/GranulesNatural ColorClear/TransparentBlackWhiteGray Color | |||
| Processing | InjectionExtrusionSheet ExtrusionProfile ExtrusionFilm ExtrusionThermoformingMachining | |||
| Compliance | FDAISO10993NSFRoHS | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ASTM D792 | |
Melt Mass Flow Rate(MFR) | |||
343°C/2.16 kg | *** g/10 min | ASTM D 1238 | |
Mold Shrinkage | |||
Flow | *** % | ASTM D955 | |
Water Absorption | *** % | ASTM D570 | 24 hr |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Modulus | *** Mpa | ASTM D638 | |
Tensile Strength | |||
Break | *** Mpa | ASTM D638 | |
Tensile Elongation | |||
Break | ***~*** % | ASTM D638 | |
Flexural Modulus | *** Mpa | ASTM D790 | |
Flexural Strength | |||
- | *** Mpa | ASTM D790 | |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Izod Notched Impact Strengh | |||
- | *** J/m | ASTM D 256 | |
Tensile Impact | *** kJ/m² | ASTM D 1822 | |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | |||
1.8 Mpa (264 psi)（18.6kg/cm²） | *** °C | ASTM D648 | |
Coefficient of Linear Thermal Expansion | |||
Flow | *** E-6 cm/cm/℃ | ASTM D 696 | |
| Flammability | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Flame Rating | |||
HB | *** mm | UL94 | ALL |
V-0 | *** mm | UL94 | NC |
Glow Wire Flammability Index(GWFI) | |||
0.8mm | *** °C | IEC 60695-2-12 | |
1.6mm | *** °C | IEC 60695-2-12 | 1.6 to 6.0 mm |
3.2mm | *** °C | IEC 60695-2-12 | 1.6 to 6.0 mm |
Glow Wire Ignition Test(GWIT) | |||
0.8mm | *** °C | IEC 60695-2-13 | |
1.6mm | *** °C | IEC 60695-2-13 | 1.6 to 6.0 mm |
3.2mm | *** °C | IEC 60695-2-13 | 1.6 to 6.0 mm |
| Electrical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Volume Resistivity | *** Ohm-cm | ASTM D257 | |
Dielectric Constant(Permittivity) | |||
60 Hz | *** - | ASTM D 150 | |
1 kHz | *** - | ASTM D 150 | |
1MHz | *** - | ASTM D 150 | |
Dissipation Factor | |||
60 Hz | *** E-4 | ASTM D 150 | |
1 kHz | *** E-4 | ASTM D 150 | |
1MHz | *** E-4 | ASTM D150 | |
Dielectric Strength | *** kV/mm | ASTM D149 |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
