An easy flowing injection moulding grade for fast processing. Used for highly stressed technical parts, such as bearings, gear wheels and electrically insulating parts such as terminals and cable connectors.
| Original Document | Technical Datasheet-ISO(English) | |||
| Solutions | Crash-active headrests-ITW | |||
| Features | Fast Cycle TimeHigh Flow | |||
| Automotive Specs | FORD WSK-M4D648-AFORD WSK-M4D647-AFORD WSS-M4D648-B1FORD WSS-M4D648-B2Stellantis MS-DB-41BMW Yes: Unspecified | |||
| Technical Notes | Tensile modulus-TemperatureTensile Strength-Moisture contentShear modulus-TemperatureStress-strainStress-strain (isochronous)(creep)Moisture absorption-Relative humidityWater absorption-Time | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ISO 1183 | |
Melt Volume Flow Rate(MVR) | |||
275°C/5 kg | *** cm³/10 min | ISO 1133 | |
Mold Shrinkage | |||
Flow | *** % | ISO 294-4 | |
Across Flow | *** % | ISO 294-4 | |
Molding Shrinkage | |||
constrained | *** % | - | |
Water Absorption | ***~*** % | ISO 62 | Equilibrium, 23°C, 50% RH |
Water Absorption | ***~*** % | ISO 62 | Saturation, 23°C |
Viscosity | *** cm³/g | ISO 307, 1157, 1628 | 0.5% in 96 % H2SO4 |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Modulus | *** Mpa | ISO 527-1/-2 | Dry |
Tensile Modulus | *** Mpa | ISO 527-1/-2 | cond. |
Tensile Strength | |||
Yield | *** Mpa | ISO 527-1/-2 | Dry |
Yield | *** Mpa | ISO 527-1/-2 | cond. |
Tensile Elongation | |||
Yield | *** % | ISO 527-1/-2 | Dry |
Yield | *** % | ISO 527-1/-2 | cond. |
Nominal Tensile Strain at Break | *** % | ISO 527-1/-2 | Dry |
Nominal Tensile Strain at Break | *** % | ISO 527-1/-2 | cond. |
Flexural Modulus | *** Mpa | ISO 178 | Dry |
Tensile Creep Modulus | |||
1000h | *** Mpa | ISO 899-1 | cond. |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Charpy Notched Impact Strengh | |||
-30℃ (-22℉) | *** kJ/m² | ISO 179/1eA | Dry |
23℃ (73℉) | *** kJ/m² | ISO 179/1eA | Dry |
23℃ (73℉) | *** kJ/m² | ISO 179/1eA | cond. |
Charpy Unnotched Impact Strengh | |||
23℃ (73℉) | *** kJ/m² | ISO 179/1eU | Dry |
23℃ (73℉) | *** kJ/m² | ISO 179/1eU | cond. |
Izod Notched Impact Strengh | |||
-30℃ (-22℉) | *** kJ/m² | ISO 180/A | Dry |
23℃ (73℉) | *** kJ/m² | ISO 180/A | Dry |
23℃ (73℉) | *** kJ/m² | ISO 180/A | cond. |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | |||
0.45 Mpa (66 psi)（4.6kg/cm²） | *** °C | ISO 75-1/-2 | |
1.8 Mpa (264 psi)（18.6kg/cm²） | *** °C | ISO 75-1/-2 | |
Specific Heat | *** J/kg-K | - | |
Coefficient of Linear Thermal Expansion | |||
Flow | ***~*** E-6/K | ISO 11359-1/-2 | 23-80℃ |
Melt Temperature(Tm) | *** °C | ISO 11357-1/-3 | DSC |
Thermal Conductivity | *** W/(m K) | DIN 52612-1 | |
Temperature at Short Circle Operation | *** °C | - | |
Processing Temperature | ***~*** °C | - | |
Mould temperature | ***~*** °C | - | |
Temperature index (TI)-Tensile Strength | |||
5000 h | *** °C | IEC 60216 | |
20000 h | *** °C | IEC 60216 | |
| Flammability | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Flame Rating | |||
V-2 | *** mm | UL94 | |
FMVSS | *** pass | FMVSS 302 | thickness d>= 1mm |
| Electrical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Volume Resistivity | *** Ohm-m | IEC 60093 | Dry |
Volume Resistivity | *** Ohm-m | IEC 60093 | cond. |
Surface Resistivity | *** Ohm | IEC 60093 | cond. |
Dielectric Constant(Permittivity) | |||
1MHz | *** - | IEC 60250 | Dry |
1MHz | *** - | IEC 60250 | cond. |
Dissipation Factor | |||
1MHz | *** E-4 | IEC 60250 | Dry |
1MHz | *** E-4 | IEC 60250 | cond. |
Comparative Tracking Index (CTI) | |||
Solution A | *** V | IEC 60112 | Dry |
Solution A | *** V | IEC 60112 | cond. |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
