TECHNYL eXten® D 219WFC V50 Black is a polyamide 6.10, reinforced with 50% of glass fibre, heat stabilized with organic stabilizers, for injection moulding. This grade offers lower water uptake, higher dimensional stability and enhanced chlorine resistance versus standard PA 6.6. It offers too an enhanced corrosion resistance, a reduction in lead levels versus standard metal solutions and an increase in ease of processing and part design freedom versus metal solutions and other plastics. It is used for cold and warm water plumbing components including, but not limited to, components in contact with drinking water systems globally where elevated levels of chlorine could be present.
| Original Document | Technical Datasheet(English) | |||
| Features | Heat StabilizedDimensional StabilityEco-friendlyBio-basedFood ContactDrinking Water ContactChemical ResistanceFilled & Reinforced | |||
| Additive | Heat Stabilizer | |||
| Appearance | Pellets/GranulesBlack | |||
| Processing | Injection | |||
| Compliance | ACSDVGW W270KTWNSFREACH (EC 1907/2006)RoHSWRAS | |||
| Reinforced | 50% Glass Fiber | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ISO 1183 | Dry |
Mold Shrinkage | |||
Flow | *** % | ISO 294-4 | Dry |
Across Flow | *** % | ISO 294-4 | Dry |
Water Absorption | *** % | ISO 62 | 24 hr,23℃ |
Water Absorption | *** % | ISO 62 | Saturation, 23°C |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Modulus | *** Mpa | ISO 527-2/1A | Conditioned,23℃ |
Tensile Modulus | *** Mpa | ISO 527-2/1A | Dry,23℃ |
Tensile Strength | |||
Break | *** Mpa | ISO 527-2/1A | Conditioned,23℃ |
Break | *** Mpa | ISO 527-2/1A | Dry,23℃ |
Tensile Elongation | |||
Break | *** % | ISO 527-2 | Dry,23℃ |
Break | *** % | ISO 527-2/1A | Conditioned,23℃ |
Flexural Modulus | *** Mpa | ASTM D790 | Dry,23℃ |
Flexural Modulus | *** Mpa | ISO 178 | Dry,23℃ |
Flexural Strength | |||
- | *** Mpa | ASTM D790 | Dry,23℃ |
- | *** Mpa | ISO 178 | Dry,23℃ |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Charpy Notched Impact Strengh | |||
23℃ (73℉) | *** kJ/m² | ISO 179/1eA | Dry |
Izod Notched Impact Strengh | |||
23℃ (73℉) | *** kJ/m² | ISO 180 | Dry |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | |||
1.8 Mpa (264 psi)（18.6kg/cm²） | *** °C | ISO 75-2/Af | Dry,Unannealed |
Melt Temperature(Tm) | *** °C | ISO 11357-3 | Dry |
| Flammability | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Flame Rating | |||
HB | *** mm | UL94 | Dry |
HB | *** mm | UL94 | Dry |
Glow Wire Flammability Index(GWFI) | |||
1.6mm | *** °C | IEC 60695-2-12 | Dry |
| Electrical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Volume Resistivity | *** Ohm-cm | IEC 60093 | Dry |
Surface Resistivity | *** Ohm | IEC 60093 | Dry |
Dielectric Constant(Permittivity) | |||
- | *** - | IEC 60250 | Dry |
Comparative Tracking Index (CTI) | |||
Solution A | *** V | IEC 60112 | Dry |
Dielectric Strength | *** kV/mm | IEC 60243-1 | Dry,2.00mm |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
