| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Density/Specific Gravity |
*** g/cm³
| ISO 1183 | |
Density/Specific Gravity |
*** g/cm³
| ASTM D792 | |
Melt Volume Flow Rate(MVR) | | | |
200°C/5.0 kg |
*** cm³/10 min | ISO 1133 | |
Melt Mass Flow Rate(MFR) | | | |
200 ℃/5 Kg |
*** g/10 min | ASTM D 1238 | |
Mold Shrinkage | | | |
- |
*** in/in | ASTM D955 | |
- |
***~*** % | ISO 294-4 | |
Water Absorption |
*** %
| ASTM D570 | Saturated at 23 °C |
Water Absorption |
*** %
| ISO 62 | Saturated at 23 °C |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Modulus |
*** psi
| ASTM D638 | |
Tensile Modulus |
*** Mpa
| ISO 527 | |
Tensile Strength | | | |
Yield |
*** psi | ASTM D638 | 23 °C |
Yield |
*** Mpa | ISO 527 | 23 °C |
Tensile Elongation | | | |
Yield |
*** % | ISO 527 | 23 °C |
Break |
*** % | ASTM D638 | 23 °C |
Nominal Tensile Strain at Break |
*** % | ISO 527 | 23 °C |
Flexural Modulus |
*** psi
| ASTM D790 | 23 °C |
Flexural Modulus |
*** Mpa
| ISO 178 | 23 °C |
Flexural Strength | | | |
- |
*** psi | ASTM D790 | 23 °C |
- |
*** Mpa | ISO 178 | 23 °C |
5% strain |
*** Mpa | - | |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Charpy Notched Impact Strengh | | | |
23℃ (73℉) |
*** kJ/m² | ISO 179/1eA | |
Charpy Unnotched Impact Strengh | | | |
23℃ (73℉) |
*** kJ/m² | ISO 179/1eU | |
Izod Notched Impact Strengh | | | |
-30℃ (-22℉) |
*** kJ/m² | ISO 180/A | |
23℃ (73℉) |
*** ft·lb/in | ASTM D256 | |
23℃ (73℉) |
*** kJ/m² | ISO 180/A | |
Instrumented Impact Energy | | | |
23℃ (73℉)peak |
*** in-lbs | ASTM D3763 | |
23℃ (73℉)Total Energy |
*** in-lbs | ASTM D3763 | |
| Hardness | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Shore A hardness |
*** A
| ISO 868 | |
Shore D hardness |
*** D
| ISO 868 | |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | | | |
0.45 Mpa (66 psi)（4.6kg/cm²） |
*** °F | ASTM D648 | Unannealed |
0.45 Mpa (66 psi)（4.6kg/cm²） |
*** °C | ISO 75 | annealed 4 h/80 °C |
1.8 Mpa (264 psi)（18.6kg/cm²） |
*** °F | ASTM D648 | Unannealed |
1.8 Mpa (264 psi)（18.6kg/cm²） |
*** °C | ISO 75 | annealed 4 h/80 °C |
Vicat Softening Temperature(VST) |
*** °F
| ASTM D1525 | B/1 ( 120 °C/h, 10N) |
Vicat Softening Temperature(VST) |
*** °C
| ISO 306 | VST/A/50 (10N, 50 °C/h) |
Vicat Softening Temperature(VST) |
*** °C
| ISO 306 | VST/B/50 (50N, 50 °C/h) |
Coefficient of Linear Thermal Expansion | | | |
- |
*** E-4/°F | ASTM D 696 | |
- |
***~*** E-6/°C | ISO 11359 | |
Processing Temperature |
***~*** °C
| - | |
| Electrical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Volume Resistivity |
*** Ohm-m
| IEC 60093 | |
Surface Resistivity |
*** Ohm
| IEC 60093 | |
Dielectric Constant(Permittivity) | | | |
100Hz |
*** - | IEC 60250 | |
Dissipation Factor | | | |
100Hz |
*** E-4 | IEC 60250 | |
1MHz |
*** E-4 | IEC 60250 | |
Comparative Tracking Index (CTI) | | | |
- |
*** V | IEC 60112 | |
| Optical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Light Transmission |
*** %
| ASTM D1003 | at 550 nm |
Haze |
*** %
| ASTM D1003 | |
Refractive Index |
*** -
| ASTM D542 | |
Refractive Index |
*** -
| ISO 489 | Sodium D Line |
| Film | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Elongation | | | |
Break |
*** % | ASTM D 882 | MD |
Break |
*** % | ASTM D 882 | TD |
Break |
*** % | ISO 527 | MD |
Tensile Modulus |
*** psi
| ASTM D 882 | MD |
Tensile Modulus |
*** psi
| ASTM D 882 | TD |
Elmondorf Tear |
*** lbs
| ASTM D 1922 | MD |
Elmondorf Tear |
*** lbs
| ASTM D 1922 | TD |
Water Vapor Transmission Rate |
*** g/100in²/day
| ASTM F 1249 | 23 °C/0% to 85% RH gradient |
Oxygen permeability |
*** cc/100in²/day
| ASTM D 3985 | 23 °C/0% RH |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
