PBT alloy Filler-reinforced / HB (0.75mm) equivalent per in-house testing, Filler 20% / Low Warpage
| Original Document | Technical Datasheet(English) | |||
| Features | Low WarpageFilled & Reinforced | |||
| Reinforced | 20% Filler | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ISO 1183 | |
Melt Volume Flow Rate(MVR) | |||
270℃/2.16 kg | *** cm³/10 min | ISO 1133 | |
Mold Shrinkage | |||
Flow | *** % | Internal | 2.00 mm |
Across Flow | *** % | Internal | 2.00 mm |
Water Absorption | *** % | ISO 62 | Saturation, 23℃ |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Modulus | *** Mpa | ISO 527-2/1 | |
Tensile Strength | |||
Break | *** Mpa | ISO 527-2/5 | |
Tensile Elongation | |||
Break | *** % | ISO 527-2/5 | |
Flexural Modulus | *** Mpa | ISO 178 | 2.0 mm/min |
Flexural Strength | |||
- | *** Mpa | ISO 178 | 2.0 mm/min |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Charpy Notched Impact Strengh | |||
23℃ (73℉) | *** kJ/m² | ISO 179 | |
Charpy Unnotched Impact Strengh | |||
23℃ (73℉) | *** kJ/m² | ISO 179 | |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | |||
0.45 Mpa (66 psi)（4.6kg/cm²） | *** °C | ISO 75-2/B | Annealed |
Coefficient of Linear Thermal Expansion | |||
Flow | *** E-6 cm/cm/℃ | ISO 11359-2 | -30 to 120℃ |
Flow | *** E-6 cm/cm/℃ | ISO 11359-2 | -30 to 35℃ |
Flow | *** E-6 cm/cm/℃ | ISO 11359-2 | 35 to 120℃ |
Across Flow | *** E-6 cm/cm/℃ | ISO 11359-2 | -30 to 120℃ |
Across Flow | *** E-6 cm/cm/℃ | ISO 11359-2 | -30 to 35℃ |
Across Flow | *** E-6 cm/cm/℃ | ISO 11359-2 | 35 to 120℃ |
| Flammability | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Flame Rating | |||
HB | *** mm | Internal | |
| Electrical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Volume Resistivity | *** Ohm-cm | IEC 60093 | |
Surface Resistivity | *** Ohm | IEC 60093 | |
Dielectric Constant(Permittivity) | |||
1MHz | *** - | IEC 60250 | |
Dissipation Factor | |||
1MHz | *** E-4 | IEC 60250 |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
