NORYL GTX902E is a low cost GTX grade especially developed for automotive (wheel)trims.
| Original Document | Technical Datasheet(English) | |||
| Solutions | Automative Wheel Covers | |||
| Availability | Europe | |||
| Applications | Automotive wheel Trims | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ISO 1183 | |
Melt Volume Flow Rate(MVR) | |||
280°C/5.0 kg | *** cm³/10 min | ISO 1133 | |
Mold Shrinkage | |||
Flow | ***~*** % | Internal | on Tensile Bar |
Water Absorption | |||
Saturation, 23°C | *** % | ISO 62 | |
Equilibrium, 23°C, 50% RH | *** % | ISO 62 | |
Abrasion resistance | |||
Taber Abrasion, CS-17, 1 kg, 1000cy | *** mg | Internal | |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Modulus | |||
- | *** Mpa | ISO 527 | 1 mm/min |
Tensile Strength | |||
Yield | *** Mpa | ISO 527 | 50 mm/min |
Break | *** Mpa | ISO 527 | 50 mm/min |
Tensile Elongation | |||
Yield | *** % | ISO 527 | 50 mm/min |
Break | *** % | ISO 527 | 50 mm/min |
Flexural Modulus | |||
- | *** Mpa | ISO 178 | 2 mm/min |
Flexural Strength | |||
Yield | *** Mpa | ISO 178 | 2 mm/min |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Charpy Notched Impact Strengh | |||
-30℃ (-22℉) | *** kJ/m² | ISO 179/1eA | 80*10*4 |
23℃ (73℉) | *** kJ/m² | ISO 179/1eA | 80*10*4 |
Izod Notched Impact Strengh | |||
-30℃ (-22℉) | *** kJ/m² | ISO 180/1A | 80*10*4 |
23℃ (73℉) | *** kJ/m² | ISO 180/1A | 80*10*4 |
| Hardness | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Ball Indentation Hardness | |||
H358/30 | *** Mpa | ISO 2039-1 | |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | |||
1.8 Mpa (264 psi)（18.6kg/cm²） | *** °C | ISO 75/Be | Edgew 120*10*4 sp=100mm |
Vicat Softening Temperature(VST) | |||
50N(5.1kg), 50℃/hr | *** °C | ISO 306 | |
50N(5.1kg), 120℃/hr | *** °C | ISO 306 | |
Coefficient of Linear Thermal Expansion | |||
Flow | *** E-6/°C | ISO 11359-2 | -30°C to 60°C |
Across Flow | *** E-6/°C | ISO 11359-2 | -30°C to 60°C |
Thermal Conductivity | |||
- | *** W/m-°C | ISO 8302 | |
Ball Pressure Test | *** °C | IEC 60695-10-2 |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
