15% Glass Fiber Reinforced, 25% Mineral Reinforced, Heat Stabilized, High Flow
| Original Document | Technical Datasheet(English) | |||
| Resin ID | PA6-(GF+MD)40 | |||
| Features | Heat StabilizedHigh FlowFilled & Reinforced | |||
| Additive | Heat Stabilizer | |||
| Processing | Injection | |||
| Automotive Specs | FCA (Fiat Chrysler Automobiles) MS-50017-CPN4759FCA (Fiat Chrysler Automobiles) MS-DB 41-CPN4759FCA (Fiat Chrysler Automobiles) MS-50017-CPN2755FCA (Fiat Chrysler Automobiles) MS-50017-CPN2927FCA (Fiat Chrysler Automobiles) MS-50017-CPN3441FCA (Fiat Chrysler Automobiles) MS-DB 41-CPN2755FCA (Fiat Chrysler Automobiles) MS-DB 41-CPN2927FCA (Fiat Chrysler Automobiles) MS-DB 41-CPN3441 | |||
| Diagrams | Viscosity-shear rateSpecific volume-temperature (pvT)Shearstress-shear rate | |||
| Reinforced | 15% Glass Fiber25% Mineral40% Glass Fiber+Minal | |||
| Physical | Dry/Cond.(Sign in to View) | Unit | Test Standard | Test Condition |
|---|---|---|---|---|
Density/Specific Gravity | ***/ *** | g/cm³ | ISO 1183 | |
Mold Shrinkage | ||||
Flow | ***/ * | % | ISO 294-4 | |
Across Flow | ***/ * | % | ISO 294-4 | |
Water Absorption | ***/ * | % | ISO 62 | |
Moisture /Humidity Absorption | ***/ * | % | ISO 62 | |
Melt Density | ***/ * | g/cm³ | - | |
| Mechanical | Dry/Cond.(Sign in to View) | Unit | Test Standard | Test Condition |
Tensile Modulus | ***/ *** | Mpa | ISO 527-1/-2 | |
Tensile Strength | ||||
Break | ***/ *** | Mpa | ISO 527-1/-2 | |
Tensile Elongation | ||||
Break | ***/ *** | % | ISO 527-1/-2 | |
Flexural Modulus | ***/ *** | Mpa | ISO 178 | |
Flexural Strength | ||||
- | ***/ *** | Mpa | ISO 178 | |
| Impact | Dry/Cond.(Sign in to View) | Unit | Test Standard | Test Condition |
Charpy Notched Impact Strengh | ||||
-30℃ (-22℉) | ***/ *** | kJ/m² | ISO 179/1eA | |
23℃ (73℉) | ***/ *** | kJ/m² | ISO 179/1eA | |
Charpy Unnotched Impact Strengh | ||||
-30℃ (-22℉) | ***/ *** | kJ/m² | ISO 179/1eU | |
23℃ (73℉) | ***/ *** | kJ/m² | ISO 179/1eU | |
| Thermal | Dry/Cond.(Sign in to View) | Unit | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | ||||
0.45 Mpa (66 psi)（4.6kg/cm²） | ***/ * | °C | ISO 75-1/-2 | |
1.8 Mpa (264 psi)（18.6kg/cm²） | ***/ * | °C | ISO 75-1/-2 | |
Specific Heat | ***/ * | J/kg-K | - | melt |
Coefficient of Linear Thermal Expansion | ||||
Flow | ***/ * | E-6/°C | ISO 11359-1/-2 | |
Across Flow | ***/ * | E-6/°C | ISO 11359-1/-2 | |
Melt Temperature(Tm) | ***/ * | °C | ISO 11357-1/-3 | 10°C/min |
Thermal Conductivity | ***/ * | W/(m K) | - | melt |
Thermal Diffusivity | ***/ * | m²/s | - | |
| Electrical | Dry/Cond.(Sign in to View) | Unit | Test Standard | Test Condition |
Volume Resistivity | ***/ *** | Ohm-m | IEC 62631-3-1 | |
Surface Resistivity | ***/ *** | Ohm | IEC 62631-3-2 | |
Dielectric Constant(Permittivity) | ||||
100Hz | ***/ *** | - | IEC 62631-2-1 | |
1MHz | ***/ *** | - | IEC 62631-2-1 | |
Dissipation Factor | ||||
100Hz | ***/ *** | E-4 | IEC 62631-2-1 | |
1MHz | ***/ *** | E-4 | IEC 62631-2-1 | |
Dielectric Strength | ***/ *** | kV/mm | IEC 60243-1 |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
