Glass fibre reinforced injection moulding grade for industrial articles and electrical insulating parts.
| Original Document | Technical Datasheet(English) | |||
| Features | Filled & Reinforced | |||
| Processing | Injection | |||
| Reinforced | 35% Glass Fiber | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ISO 1183 | |
Melt Volume Flow Rate(MVR) | |||
275°C/5 kg | *** cm³/10 min | ISO 1133 | |
Mold Shrinkage | |||
- | *** % | Internal | constrained |
Water Absorption | ***~*** % | ISO 62 | saturation in water at 23°C |
Moisture /Humidity Absorption | ***~*** % | ISO 62 | equilibrium 23°C/50% r.h. |
Viscosity | *** cm³/g | ISO 307, 1157, 1628 | 0.5% in 96% H2SO4 |
Halogen content | *** mg/kg | DIN 51408-2 | |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Modulus | *** Mpa | ISO 527-1/-2 | Cond. |
Tensile Modulus | *** Mpa | ISO 527-1/-2 | Dry |
Tensile Strength | |||
Break | *** Mpa | ISO 527-1/-2 | Cond. |
Break | *** Mpa | ISO 527-1/-2 | Dry |
Tensile Elongation | |||
Break | *** % | ISO 527-1/-2 | Cond. |
Break | *** % | ISO 527-1/-2 | Dry |
Flexural Modulus | *** Mpa | ISO 178 | Cond. |
Flexural Modulus | *** Mpa | ISO 178 | Dry |
Flexural Strength | |||
- | *** Mpa | ISO 178 | Cond. |
- | *** Mpa | ISO 178 | Dry |
Tensile Creep Modulus | |||
1000h | *** Mpa | ISO 899-1 | strain ≤ 0.5%, 23°C |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Charpy Notched Impact Strengh | |||
-30℃ (-22℉) | *** kJ/m² | ISO 179/1eA | Dry |
23℃ (73℉) | *** kJ/m² | ISO 179/1eA | Cond. |
23℃ (73℉) | *** kJ/m² | ISO 179/1eA | Dry |
Charpy Unnotched Impact Strengh | |||
-30℃ (-22℉) | *** kJ/m² | ISO 179/1eU | Dry |
23℃ (73℉) | *** kJ/m² | ISO 179/1eU | Cond. |
23℃ (73℉) | *** kJ/m² | ISO 179/1eU | Dry |
Izod Notched Impact Strengh | |||
23℃ (73℉) | *** J/m | ASTM D256 | Cond. |
23℃ (73℉) | *** J/m | ASTM D256 | Dry |
23℃ (73℉) | *** kJ/m² | ISO 180/A | Cond. |
23℃ (73℉) | *** kJ/m² | ISO 180/A | Dry |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | |||
0.45 Mpa (66 psi)（4.6kg/cm²） | *** °C | ISO 75-1/-2 | |
1.8 Mpa (264 psi)（18.6kg/cm²） | *** °C | ISO 75-1/-2 | |
Specific Heat | *** J/kg-K | - | |
Coefficient of Linear Thermal Expansion | |||
Flow | *** E-6/K | ISO 11359-1/-2 | (23-55)°C |
Across Flow | *** E-6/K | ISO 11359-1/-2 | (23-55)°C |
Melt Temperature(Tm) | *** °C | ISO 11357-1/-3 | DSC |
Thermal Conductivity | *** W/(m K) | DIN 52612-1 | |
Temperature at Short Circle Operation | *** °C | - | |
Processing Temperature | ***~*** °C | - | Injection moulding/Extrusion |
Mould temperature | ***~*** °C | - | Injection moulding |
Temperature index (TI)-Tensile Strength | |||
5000 h | *** °C | IEC 60216 | 50% loss of tensile strength |
20000 h | *** °C | IEC 60216 | 50% loss of tensile strength |
| Flammability | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Flame Rating | |||
HB | *** mm | IEC 60695-11-10 | |
FMVSS | *** pass | FMVSS 302 | Thickness ≥ 1 mm |
Burning Rate | *** mm/min | ISO 3795 | Thickness ≥ 1 mm |
| Electrical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Volume Resistivity | *** Ohm-m | IEC 62631-3-1 | Cond. |
Volume Resistivity | *** Ohm-m | IEC 62631-3-1 | Dry |
Surface Resistivity | *** Ohm | IEC 62631-3-2 | Cond. |
Dielectric Constant(Permittivity) | |||
1MHz | *** - | IEC 62631-2-1 | Cond. |
1MHz | *** - | IEC 62631-2-1 | Dry |
Dissipation Factor | |||
1MHz | *** E-4 | IEC 62631-2-1 | Cond. |
1MHz | *** E-4 | IEC 62631-2-1 | Dry |
Dielectric Strength | *** kV/mm | IEC 60243-1 | Cond.,K20/K20, (60*60*1 mm³) |
Dielectric Strength | *** kV/mm | IEC 60243-1 | Dry, K20/K20, (60*60*1 mm³) |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
