PBT injection moulding grade.
Characteristics
1)excellent gloss
2)excellent electrical property
3)excellent temperature resistance, high heat distortion temperature.
4)excellent mechanic and chemical property
5)excellent weatherability
6)excellent wear property
7)excellent moldability
8)High resistance to fuels, oil, fats and many solvents
| Original Document | Technical Datasheet(English) | |||
| Features | Heat ResistanceHigh GlossWear/Abrasion ResistanceEasy processingWeather ResistanceChemical ResistanceFuels ResistantOil ResistantAnti-Solvent | |||
| Appearance | Pellets/GranulesBlack | |||
| Processing | Injection | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ASTM D792 | |
Melt Mass Flow Rate(MFR) | |||
250°C/2.16 kg | ***~*** g/10min | ASTM D1238 | |
Mold Shrinkage | |||
Flow | ***~*** % | ASTM D955 | 1.60 mm |
Across Flow | ***~*** % | ASTM D955 | 1.60 mm |
Moisture /Humidity Absorption | *** % | ASTM D 570 | 24h |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Strength | |||
- | *** kg/cm² | ASTM D 638 | |
Tensile Elongation | |||
- | *** % | ASTM D 638 | |
Flexural Modulus | *** kg/cm² | ASTM D790 | |
Flexural Strength | |||
- | *** kg/cm² | ASTM D790 | |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Izod Notched Impact Strengh | |||
- | *** kg·cm/cm | ASTM D 256 | 6.35 mm |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | |||
0.45 Mpa (66 psi)（4.6kg/cm²） | *** °C | ASTM D648 | |
1.8 Mpa (264 psi)（18.6kg/cm²） | *** °C | ASTM D648 | |
Coefficient of Linear Thermal Expansion | |||
- | *** E-6 cm/cm/℃ | ASTM D 696 | |
Melt Temperature(Tm) | *** °C | DSC | |
| Flammability | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Flame Rating | |||
HB | *** mm | UL94 | |
| Electrical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Volume Resistivity | *** Ohm-cm | ASTM D257 | |
Surface Resistivity | *** Ohm | ASTM D257 | |
Dielectric Constant(Permittivity) | |||
60 Hz | *** - | ASTM D 150 | |
Dissipation Factor | |||
60 Hz | *** E-4 | ASTM D 150 | |
Dielectric Strength | *** kV/mm | ASTM D149 | 2mm thickness |
Arc Resistance | *** sec | ASTM D495 |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
