Amorphous Polymers – Optical Diffusion Grade (Injection molding)
For LED ILLUMINATION Applications
| Original Document | Technical Datasheet(English) | |||
| Features | Light Diffusion | |||
| Processing | Injection | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ISO 1183 | |
Melt Volume Flow Rate(MVR) | |||
300°C/1.2 kg | *** cm³/10 min | ISO 1133 | |
Mold Shrinkage | |||
Flow | ***~*** % | Internal | 2 mm |
Across Flow | ***~*** % | Internal | 2 mm |
Outdoor Suitability UL F1/F2 | |||
F2 | *** - | UL 746C | |
Water Absorption | *** % | ISO 62 | 24 hrs. 50%RH |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Strength | |||
Yield | *** Mpa | ISO 527 | |
Tensile Elongation | |||
Break | *** % | ISO 527 | |
Flexural Modulus | *** Mpa | ISO 178 | |
Flexural Strength | |||
- | *** Mpa | ISO 178 | |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Charpy Notched Impact Strengh | |||
23℃ (73℉) | *** kJ/m² | ISO 179 | |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | |||
1.8 Mpa (264 psi)（18.6kg/cm²） | *** °C | ISO 75/A | |
Relative Temperature Index(RTI), Imp | |||
- | *** °C | UL 746B | |
Relative Temperature Index(RTI), Elec | |||
- | *** °C | UL 746B | |
Relative Temperature Index(RTI), Str | |||
- | *** °C | UL 746B | |
Coefficient of Linear Thermal Expansion | |||
Flow | *** E-6 cm/cm/℃ | TMA | |
Processing Temperature | ***~*** °C | - | |
Mould temperature | ***~*** °C | - | |
| Flammability | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Flame Rating | |||
HB | *** mm | UL94 | |
HB | *** mm | UL94 | |
HB | *** mm | UL94 | |
V-2 | *** mm | UL94 | |
V-2 | *** mm | UL94 | |
V-2 | *** mm | UL94 | |
V-2 | *** mm | UL94 | |
| Electrical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Dielectric Constant(Permittivity) | |||
- | *** - | IEC 60250 | |
Dissipation Factor | |||
- | *** E-4 | IEC 60250 | |
Comparative Tracking Index (CTI) | |||
Solution A | *** PLC | IEC 60112 | |
Dielectric Strength | *** kV/mm | ASTM D149 | |
Arc Resistance | *** PLC | ASTM D495 | |
High Voltage Arc Tracking Rate(HVTR) | *** PLC | UL 746A | |
Hot Wire Ignition(HWI) | *** PLC | UL 746A | 1.5mm |
Hot Wire Ignition(HWI) | *** PLC | UL 746A | 3.0mm |
High Ampere Arc Ignition(HAI) | PLC | UL 746A | 1.5mm |
High Ampere Arc Ignition(HAI) | PLC | UL 746A | 3.0mm |
| Optical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Light Transmission | *** % | ISO 13468 | 1mmt |
Light Transmission | *** % | ISO 13468 | 2mmt |
Light Transmission | *** % | ISO 13468 | 3mmt |
Haze | *** % | ASTM D1003 | 1mmt |
Haze | *** % | ASTM D1003 | 2mmt |
Haze | *** % | ASTM D1003 | 3mmt |
Diffusion Angle | *** % | Internal | 1mmt |
Diffusion Angle | *** % | Internal | 2mmt |
Diffusion Angle | *** % | Internal | 3mmt |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
