POKETONE Polymer M630A is a general-purpose injection moulding grade with mechanical properties which classify it as an engineering thermoplastic. This grade has an excellent balance of stiffness and toughness over a broad temperature range, high resilience and good wear resistance.This grade exhibits very good processability, good impact resistance, high resilience and good creep performance. POKETONE Polymer M630A can also withstand short-term exposure to elevated temperatures. Moreover this polymer exhibits a high resistance to hydrocarbons, solvents, salt solutions, weak acids and weak bases.
| Original Document | Technical Datasheet(English) | |||
| Features | High Impact | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ASTM D792 | |
Melt Volume Flow Rate(MVR) | |||
240℃/2.16 kg | *** cm³/10 min | ISO 1133 | |
Melt Mass Flow Rate(MFR) | |||
240℃/2.16kg | *** g/10 min | ASTM D 1238 | |
240℃/2.16kg | *** g/10 min | ISO 1133 | |
Mold Shrinkage | |||
Flow | *** % | ASTM D955 | 2mm |
Flow | *** % | ASTM D955 | 3mm |
Across Flow | *** % | ASTM D955 | 2mm |
Across Flow | *** % | ASTM D955 | 3mm |
Water Absorption | *** % | ASTM D570 | |
Water Absorption | *** % | ISO 62 | |
Moisture /Humidity Absorption | *** % | ISO 62 | |
Moisture /Humidity Absorption | *** % | ASTM D 570 | |
Abrasion resistance | *** mg/1000cy | ASTM D 1044 | 1 kg load, CS-17 wheel |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Modulus | *** Mpa | ASTM D638 | |
Tensile Modulus | *** Mpa | ISO 527-1 | |
Tensile Strength | |||
Yield | *** Mpa | ASTM D638 | |
Yield | *** Mpa | ISO 527-1 | |
Tensile Elongation | |||
Yield | *** % | ASTM D638 | |
Yield | *** % | ISO 527-1 | |
Break | *** % | ASTM D638 | |
Break | *** % | ISO 527-1 | |
Flexural Modulus | *** Mpa | ASTM D790 | |
Flexural Modulus | *** Mpa | ISO 178 | |
Flexural Strength | |||
- | *** Mpa | ASTM D790 | |
- | *** Mpa | ISO 178 | |
Coefficient of Friction | *** - | Internal | Friction against steel,1.3 MPa 0.06 m/sec |
Coefficient of Friction | *** - | Internal | Friction agatinst self,1.3 MPa 0.06 m/sec |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Charpy Notched Impact Strengh | |||
-30℃ (-22℉) | *** kJ/m² | ISO 179/1eA | |
-10℃ (14℉) | *** kJ/m² | ISO 179/1eA | |
23℃ (73℉) | *** kJ/m² | ISO 179/1eA | |
Charpy Unnotched Impact Strengh | |||
23℃ (73℉) | *** kJ/m² | ISO 179/1eU | |
Izod Notched Impact Strengh | |||
-30℃ (-22℉) | *** J/m | ASTM D256 | |
-30℃ (-22℉) | *** kJ/m² | ISO 180/A | |
-10℃ (14℉) | *** J/m | ASTM D256 | |
-10℃ (14℉) | *** kJ/m² | ISO 180/A | |
23℃ (73℉) | *** J/m | ASTM D256 | |
23℃ (73℉) | *** kJ/m² | ISO 180/A | |
Izod Unnotched Impact Strengh | |||
23℃ (73℉) | *** J/m | ASTM D256 | |
23℃ (73℉) | *** kJ/m² | ISO 180/1U | |
Multiaxial Impact | *** J | ISO 6603 | |
| Hardness | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Rockwell R | *** R | ASTM D785 | |
Shore D hardness | *** D | ISO 868 | |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | |||
0.45 Mpa (66 psi)（4.6kg/cm²） | *** °C | ASTM D648 | |
0.45 Mpa (66 psi)（4.6kg/cm²） | *** °C | ISO 75 | |
1.8 Mpa (264 psi)（18.6kg/cm²） | *** °C | ASTM D648 | |
1.8 Mpa (264 psi)（18.6kg/cm²） | *** °C | ISO 75 | |
Vicat Softening Temperature(VST) | *** °C | ASTM D1525 | 5 kg |
Vicat Softening Temperature(VST) | *** °C | ISO 306 | |
Coefficient of Linear Thermal Expansion | |||
- | *** E-6/°C | ASTM D E831 | 25℃ to 55℃ |
Melt Temperature(Tm) | *** °C | ASTM D3418 | |
Melt Temperature(Tm) | *** °C | ISO 11357 | |
| Electrical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Volume Resistivity | *** Ohm-cm | ASTM D257 | |
Surface Resistivity | *** Ohm | ASTM D257 | |
Dielectric Constant(Permittivity) | |||
60 Hz | *** - | ASTM D 150 | |
Dissipation Factor | |||
60 Hz | *** E-4 | ASTM D 150 | |
Dielectric Strength | *** kV/mm | ASTM D149 | 2mm |
Dielectric Strength | *** kV/mm | ASTM D149 | 3mm |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
