Viton™ A-601C* fluoroelastomer is a new generation incorporated cure “A-family” dipolymer designed for compression molding of sealing devices that must meet major fluoroelastomer specifications. In addition to the chemical and heat resistance characteristics typical of fluoroelastomers, Viton™ A-601C offers significant improvements in processing and rheology. Viton™ A-601C can be blended with similar Viton™ types to provide a range of processing performance and physical properties.
Features
• Fully precompounded
– O-ring curative level
• Improved processing for a high viscosity polymer
– Improved mold flow
– Easier mold release
– Less mold fouling
• Excellent scorch safety
• Excellent physical properties
– Improved compression set resistance
Applications
• Compression molding of O-rings, gaskets, and other sealing devices
• Applications where a higher polymer viscosity is needed for molding operations. Can be used to modify viscosity of other types of Viton™
• Can be formulated to meet FKM specifications Mil-R-83248C and AMS 7276E
| Original Document | Technical Datasheet(English) | |||
| Appearance | SlabWhite | |||
| Processing | ExtrusionCompression Moulding | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | Internal | |
Mooney Viscosity | *** MU | Internal | ML 1+10, 121°C |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Strength | |||
- | *** Mpa | ASTM D 412 | 23 °C, After aging 168 hr at 200 °C |
- | *** Mpa | ASTM D 412 | 23 °C, After aging 70 hr at 200 °C |
- | *** Mpa | ASTM D 412 | 23 °C, After aging 70 hr at 250 °C |
- | *** Mpa | ASTM D 412 | 23 °C, After aging 70 hr at 275 °C |
- | *** Mpa | ASTM D 412 | 23 °C, Original, No post-cure |
at 100% strain | *** Mpa | ASTM D 412 | 23 °C, After aging 168 hr at 200 °C |
at 100% strain | *** Mpa | ASTM D 412 | 23 °C, After aging 70 hr at 200 °C |
at 100% strain | *** Mpa | ASTM D 412 | 23 °C, After aging 70 hr at 250 °C |
at 100% strain | *** Mpa | ASTM D 412 | 23 °C, After aging 70 hr at 275 °C |
at 100% strain | *** Mpa | ASTM D 412 | 23 °C, Original, No post-cure |
Tensile Elongation | |||
Break | *** % | ASTM D 412 | 23 °C, After aging 168 hr at 200 °C |
Break | *** % | ASTM D 412 | 23 °C, After aging 70 hr at 200 °C |
Break | *** % | ASTM D 412 | 23 °C, After aging 70 hr at 250 °C |
Break | *** % | ASTM D 412 | 23 °C, After aging 70 hr at 275 °C |
Break | *** % | ASTM D 412 | 23 °C, Original, No post-cure |
Compression Set | *** % | ASTM D 395 | 168 hr at 200 °C, Method B, O-Rings |
Compression Set | *** % | ASTM D 395 | 22 hr at 175 °C, Method B, O-Rings |
Compression Set | *** % | ASTM D 395 | 22 hr at 200 °C, Method B, O-Rings |
Compression Set | *** % | ASTM D 395 | 70 hr at 200 °C, Method B, O-Rings |
Compression Set | *** % | ASTM D 395 | 70 hr at 23 °C, Method B, O-Rings |
Compression Set | *** % | ASTM D 395 | 70 hr at 232 °C, Method B, O-Rings |
| Hardness | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Shore A hardness | *** A | ASTM D 2240 | 23 °C, After aging 168 hr at 200 °C |
Shore A hardness | *** A | ASTM D 2240 | 23 °C, After aging 70 hr at 200 °C |
Shore A hardness | *** A | ASTM D 2240 | 23 °C, After aging 70 hr at 250 °C |
Shore A hardness | *** A | ASTM D 2240 | 23 °C, After aging 70 hr at 275 °C |
Shore A hardness | *** A | ASTM D 2240 | 23 °C, Original, No post-cure |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
