A soft, colorable, specialty, non-hygroscopic thermoplastic vulcanizate (TPV) in the thermoplastic elastomer (TPE) family. It is designed for use in non fatty food contact applications. This grade of Santoprene TPV is shear-dependent and can be processed on conventional thermoplastics equipment for injection molding or blow molding. It is polyolefin based and recyclable within the manufacturing stream.
Key Features
• This product, in principle, can be used in food contact applications in the USA (FDA). Migration or use limitations may apply.
• Certified by NSF to NSF/ANSI Standard 51: Food Equipment Materials - Plastics, materials and components used in food equipment.
• UL listed: file #QMFZ2.E80017, Plastics - Component; file #QMFZ8.E80017, Plastics Certified For Canada - Component.
• Recommended for applications requiring excellent flex fatigue resistance.
• Non-hygroscopic product; requires little to no drying before processing.
• Neutral, easy coloring formulation.
| Original Document | Technical Datasheet(English) Technical Datasheet(Chinese) | |||
| Features | Good ColoringFood ContactLow Moisture AbsorptionSoft | |||
| Appearance | Pellets/GranulesNatural Color | |||
| Processing | InjectionBlow MoldingInjection Blow MoldingExtrusion Blow Molding | |||
| Compliance | ANSIFDANSFRoHSUL QMFZ2 | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ISO 1183 | |
Density/Specific Gravity | *** g/cm³ | ASTM D792 | |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Strength | |||
Break | *** Mpa | ASTM D 412 | Across Flow, 23°C |
Break | *** Mpa | ISO 37 | Across Flow, 23°C |
at 100% strain | *** Mpa | ASTM D 412 | Across Flow, 23°C |
at 100% strain | *** Mpa | ISO 37 | Across Flow, 23°C |
Tensile Elongation | |||
Break | *** % | ASTM D 412 | Across Flow, 23°C |
Break | *** % | ISO 37 | Across Flow, 23°C |
Compression Set | *** % | ASTM D 395 | 70°C, 22 hr, Type 1 |
Compression Set | *** % | ISO 815 | 70°C, 22 hr, Type A |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Brittleness Temperature | *** °C | ASTM D 746 | |
Brittleness Temperature | *** °C | ISO 812 | |
| Hardness | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Shore A hardness | *** A | ISO 868 | 15 sec, 23°C |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Relative Temperature Index(RTI), Elec | |||
- | *** °C | UL 746 | |
Relative Temperature Index(RTI), Str | |||
- | *** °C | UL 746 | |
| Flammability | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Flame Rating | |||
HB | *** mm | UL94 | |
HB | *** mm | UL94 | |
| Aging | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Hardness(Heat Aging) | *** - | ISO 188 | Change in Air, 150°C, 168 hr |
Hardness(Heat Aging) | *** - | ASTM D573 | Change in Air, 150°C, 168 hr |
Tensile Strength(Heat Aging) | *** % | ISO 188 | Change in Air, 150°C, 168 hr |
Tensile Strength(Heat Aging) | *** % | ASTM D573 | Change in Air, 150°C, 168 hr |
Elonggation(Heat Aging) | *** % | ISO 188 | Change in Air, 150°C, 168 hr |
Elonggation(Heat Aging) | *** % | ASTM D573 | Change in Air, 150°C, 168 hr |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
