A soft, black, UV resistant thermoplastic vulcanizate (TPV) in the thermoplastic elastomer (TPE) family. This material combines good physical properties and chemical resistance, and is designed for thin wall or complex profile extrusion applications. This grade of Santoprene™ TPV is shear-dependent and can be processed on conventional thermoplastics equipment for extrusion. It is polyolefin based and recyclable within the manufacturing stream.
Key Features
• Recommended for applications requiring excellent flex fatigue resistance.
• Excellent ozone resistance.
• Designed for improved UV resistance.
• Designed for extruding thin wall sections with excellent definition (down to 0.33 mm [0.013"] radius) and to maximize run length with minimal build-up of material on screen packs or narrow sections of dies.
| Original Document | Technical Datasheet(English) Technical Datasheet(Chinese) | |||
| Features | Fatigue ResistantUV StabiltiyOzone ResistantChemical ResistanceSoft | |||
| Appearance | Pellets/GranulesBlack | |||
| Processing | ExtrusionSheet ExtrusionProfile Extrusion | |||
| Compliance | RoHS | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ISO 1183 | |
Density/Specific Gravity | *** g/cm³ | ASTM D792 | |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Strength | |||
Break | *** Mpa | ASTM D 412 | Across Flow, 23°C |
Break | *** Mpa | ISO 37 | Across Flow, 23°C |
at 100% strain | *** Mpa | ASTM D 412 | Across Flow, 23°C |
at 100% strain | *** Mpa | ISO 37 | Across Flow, 23°C |
Tensile Elongation | |||
Break | *** % | ASTM D 412 | Across Flow, 23°C |
Break | *** % | ISO 37 | Across Flow, 23°C |
Tear Strength | *** kN/m | ISO 34 | Across Flow, 23°C, Method Ba, Angle (Unnicked) |
Compression Set | *** % | ASTM D 395 | 125°C, 70 hr, Type 1 |
Compression Set | *** % | ASTM D 395 | 70°C, 22 hr, Type 1 |
Compression Set | *** % | ISO 815 | 125°C, 70 hr, Type A |
Compression Set | *** % | ISO 815 | 70°C, 22 hr, Type A |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Brittleness Temperature | *** °C | ASTM D 746 | |
Brittleness Temperature | *** °C | ISO 812 | |
| Hardness | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Shore A hardness | *** A | ISO 868 | 15 sec, 23°C |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Continuous Use Temperature | |||
Long term | *** °C | SAE J2236 | 1008 hr |
| Electrical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Dielectric Constant(Permittivity) | |||
- | *** - | IEC 60250 | 23°C, 1.93 mm |
- | *** - | ASTM D150 | 23°C, 1.93 mm |
Dielectric Strength | *** kV/mm | ASTM D149 | 23°C, 2.00 mm |
| Aging | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Hardness(Heat Aging) | *** - | ISO 188 | Change in Air, 150°C, 168 hr |
Hardness(Heat Aging) | *** - | ASTM D573 | Change in Air, 150°C, 168 hr |
Tensile Strength(Heat Aging) | *** % | ISO 188 | Change in Air, 150°C, 168 hr |
Tensile Strength(Heat Aging) | *** % | ASTM D573 | Change in Air, 150°C, 168 hr |
Elonggation(Heat Aging) | *** % | ISO 188 | Change in Air, 150°C, 168 hr |
Elonggation(Heat Aging) | *** % | ASTM D573 | Change in Air, 150°C, 168 hr |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
