MPDE NG 6995 is a Medium Density Polyethylene Resin produced in the Gas Phase technology. It is designed for blown film applications providing good processability and seal properties. It offers good tear and impact resistance.
Main Characteristics:
Monolayer and multilayer blown film
General purpose bags
Complies with:
U.S. FDA 21 CFR 177.1520 (c) 3.2a
European Commission Regulation (EU) No 10/2011
Consult the regulation for complete details.
| Original Document | Technical Datasheet-ASTM(English) | |||
| Processing | Blown Film | |||
| Compliance | EU 2011/10/ECFDA | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ASTM D792 | |
Melt Mass Flow Rate(MFR) | |||
190℃/5 kg | *** g/10 min | ASTM D 1238 | |
190℃/21.6 kg | *** g/10 min | ASTM D 1238 | |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Strength | |||
Yield | *** Mpa | ASTM D638 | Compression Molded |
Break | *** Mpa | ASTM D638 | Compression Molded |
Tensile Elongation | |||
Break | *** % | ASTM D638 | Compression Molded |
Flexural Modulus | *** Mpa | ASTM D790 | Compression Molded |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Izod Notched Impact Strengh | |||
- | *** J/m | ASTM D 256 | Compression Molded |
| Hardness | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Shore D hardness | *** D | ASTM D 2240 | Compression Molded |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Processing Temperature | *** °C | - | Melt Temperature |
| Optical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Haze | *** % | ASTM D1003 | |
Gloss | *** - | ASTM D 2457 | 45° |
| Film | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Strength | |||
Yield | *** Mpa | ASTM D 882 | MD |
Yield | *** Mpa | ASTM D 882 | TD |
Break | *** Mpa | ASTM D 882 | MD |
Break | *** Mpa | ASTM D 882 | TD |
Tensile Elongation | |||
Break | *** % | ASTM D 882 | MD |
Break | *** % | ASTM D 882 | TD |
Puncture resistance | *** J/cm³ | ASTM D 5748 | 15 µm |
Elmondorf Tear | *** g | ASTM D 1922 | MD |
Elmondorf Tear | *** g | ASTM D 1922 | TD |
Secant Modulus | *** Mpa | ASTM D 882 | 1% Secant, MD |
Secant Modulus | *** Mpa | ASTM D 882 | 1% Secant, TD |
Secant Modulus | *** Mpa | ASTM D 882 | 2% Secant, MD |
Secant Modulus | *** Mpa | ASTM D 882 | 2% Secant, TD |
Dart Drop Impact | *** g | ASTM D 1709 |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
