DOW LDPE 310E is a fractional melt index low density polyethylene resin. DOW LDPE 310E has been specially designed for superior processability on blown film lines leading to significant output improvements. The resin offers additionally excellent draw down. It can be used pure or in blends with LLDPE resins.
Applications:
lamination film, shrink film, and stretch film
Main Characteristics:
Excellent processability and draw down
Good physical properties in blends with LLDPE
Can be readily extruded using conventional blown film techniques at melt temperatures between 160 and 195°C
Complies with:
U.S. FDA 21 CFR 177.1520 ( c )2.2
EU, No 10/2011
U.S. FDA-DMF
Canadian HPFB No Objection
Consult the regulations for complete details.
| Original Document | Technical Datasheet-ASTM(English) | |||
| Processing | Blown Film | |||
| Compliance | Drug Master FileEU 2011/10/ECFDAHPFB (Canada) | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ASTM D792 | |
Melt Mass Flow Rate(MFR) | |||
190℃/2.16 kg | *** g/10min | ASTM D1238 | |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Coefficient of Friction | ***~*** - | ASTM 1894 | |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Processing Temperature | ***~*** °C | - | Melt Temperature |
| Optical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Haze | *** % | ASTM D1003 | 50 µm, Blown Film |
Gloss | *** - | ASTM D 2457 | 45°, 50 µm, Blown Film |
| Film | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Strength | |||
Yield | *** Mpa | ASTM D 882 | MD, 50 µm, Blown Film |
Yield | *** Mpa | ASTM D 882 | TD, 50 µm, Blown Film |
Break | *** Mpa | ASTM D 882 | MD, 50 µm, Blown Film |
Break | *** Mpa | ASTM D 882 | TD, 50 µm, Blown Film |
Tensile Elongation | |||
Break | *** % | ASTM D 882 | MD, 50 µm, Blown Film |
Break | *** % | ASTM D 882 | TD, 50 µm, Blown Film |
Piercing strength | *** N | Internal | 50 µm |
Puncture resistance | *** J/cm³ | Internal | 50 µm |
Puncture resistance | *** J | Internal | 50 µm |
Elmondorf Tear | *** g | ASTM D 1922 | MD, 50 µm, Blown Film |
Elmondorf Tear | *** g | ASTM D 1922 | TD, 50 µm, Blown Film |
Secant Modulus | *** Mpa | ASTM D 882 | 2% Secant, MD, 50 µm, Blown Film |
Secant Modulus | *** Mpa | ASTM D 882 | 2% Secant, TD, 50 µm, Blown Film |
Dart Drop Impact | *** g | ASTM D 1709 | 50 µm, Blown Film |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
