DOWLEX™ NG 5056.01G Polyethylene Resin is a next generation linear low density polyethylene resin designed for high quality blown film applications requiring a combination of excellent optical properties, tear strength and sealability, and a very good toughness/stiffness balance. DOWLEX NG5056.01G Polyethylene Resin is also designed to offer a very low gel level making it ideal for use in lamination films and other specialty packaging. This resin contains slip and antiblocking additives.
Note: DOWLEX NG 5056.01G Polyethylene Resin should comply with FDA regulation 177.1520 and with most European food contact regulations when used unmodified and processed according to good manufacturing practices for food contact applications. Please, contact your nearest Dow office regarding food contact compliance statements. The purchaser remains responsible for determining whether the use complies with all relevant regulations.
Applications:
High clarity tissue overwrap
Produce bags
Food packaging films
Lamination film
| Original Document | Technical Datasheet(English) | |||
| Additive | Slip agentAntiblock | |||
| Processing | Blown Film | |||
| Compliance | EU 2011/10/ECFDA | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ASTM D792 | |
Melt Mass Flow Rate(MFR) | |||
190℃/2.16 kg | *** g/10min | ISO 1133 | |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Coefficient of Friction | *** - | ASTM 1894 | vs. Itself - Dynamic |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Vicat Softening Temperature(VST) | *** °C | ASTM D1525 | |
Processing Temperature | ***~*** °C | - | Extrusion |
| Optical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Haze | *** % | ISO 14782 | 50 µm |
Gloss | *** - | ASTM D 2457 | 45°, 50 µm |
| Film | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Strength | |||
Yield | *** Mpa | ISO 527-3 | MD, 50 µm |
Yield | *** Mpa | ISO 527-3 | TD, 50 µm |
Break | *** Mpa | ISO 527-3 | MD, 50 µm |
Break | *** Mpa | ISO 527-3 | TD, 50 µm |
Tensile Elongation | |||
Break | *** % | ISO 527-3 | MD, 50 µm |
Break | *** % | ISO 527-3 | TD, 50 µm |
Tensile Modulus | *** Mpa | ISO 527-3 | 2% Secant, MD, 50 µm |
Tensile Modulus | *** Mpa | ISO 527-3 | 2% Secant, TD, 50 µm |
Piercing strength | *** N | ASTM D5748 | 50 µm |
Puncture resistance | *** J | ASTM D 5748 | 50 µm |
Elmondorf Tear | *** g | ASTM D 1922 | MD, 50 µm |
Elmondorf Tear | *** g | ASTM D 1922 | TD, 50 µm |
Dart Drop Impact | *** g | ISO 7765-1 | 50 µm |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
