DOWLEX™ NG 2429.01G Polyethylene Resin is an ethylene octene copolymer for rotational moulding and is specifically designed for applications requiring excellent environmental stress crack resistance and impact strength combined with low warpage and good processing. DOWLEX NG 2429.01G is fully heat and UV stabilized resulting in a wide processing latitude, good colour retention, and long life expectancy.
Intermediate bulk containers
Drums for chemicals
Boats, freezer containers, fish crates and tanks
Complies with U.S. FDA 21 CFR 177.1520 (c) 3.1a
Consult the regulations for complete details.
| Original Document | Technical Datasheet(English) | |||
| Features | Good Impact ResistanceHeat StabilizedLow WarpageEasy processingUV StabiltiyESCR | |||
| Processing | Rotational Molding | |||
| Compliance | FDA | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ISO 1183 | |
Melt Mass Flow Rate(MFR) | |||
190℃/2.16 kg | *** g/10min | ISO 1133 | |
Environmental Stress Cracking Resistance | *** Hours | ASTM D 1693 | 50°C, 10% Antarox, Rotational Molded |
Environmental Stress Cracking Resistance | *** Hours | ASTM D 1693 | 50°C, 100% Antarox, Compression Molded |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Strength | |||
Yield | *** Mpa | ISO 527-2 | Compression Molded |
Yield | *** Mpa | ISO 527-2 | Rotational Molded |
Break | *** Mpa | ISO 527-2 | Compression Molded |
Break | *** Mpa | ISO 527-2 | Rotational Molded |
Tensile Elongation | |||
Break | *** % | ISO 527-2 | Compression Molded |
Break | *** % | ISO 527-2 | Rotational Molded |
Flexural Modulus | *** Mpa | ISO 178 | 1% Secant, Compression Molded |
Tear Strength | *** MPa | DIN 53515 | Compression Molded |
Tear Strength | *** MPa | DIN 53515 | Rotational Molded |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Multiaxial Impact | *** J | ISO 6603 | -20°C, 1.00 mm, Compression Molded |
Multiaxial Impact | *** J | ISO 6603 | 23°C, 1.00 mm, Compression Molded |
Multiaxial Impact | *** J | ISO 6603 | 23°C, Rotational Molded |
| Hardness | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Shore D hardness | *** D | ISO 868 | Compression Molded |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | |||
1.8 Mpa (264 psi)（18.6kg/cm²） | *** °C | ISO 75-2/A | Unannealed |
Vicat Softening Temperature(VST) | *** °C | ISO 306/A120 | |
Melt Temperature(Tm) | *** °C | DSC | |
Freezing temperature | *** °C | DSC |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
