DuraGrip® DGR 6030BK is designed to be a general purpose Thermoplastic Elastomer (TPE) that is easy to use in injection molding and extrusion processes. DGR 6030BK has an excellent soft touch feel, will bond to olefinics, and is easy to color. DuraGrip® is not hygroscopic and under normal conditions does not require drying.
| Original Document | Technical Datasheet(English) | |||
| Features | Good ColoringGood AdhesionSoft | |||
| Appearance | Pellets/GranulesBlack | |||
| Processing | InjectionExtrusion | |||
| Compliance | RoHSWEEE(EU 2002/96/EC) | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ISO 1183 | |
Density/Specific Gravity | *** g/cm³ | ASTM D792 | |
Mold Shrinkage | |||
Flow | *** % | ASTM D955 | 1.59 mm |
Flow | *** % | ASTM D955 | 3.18 mm |
Flow | *** % | ISO 294-4 | 1.59 mm |
Flow | *** % | ISO 294-4 | 3.18 mm |
Across Flow | *** % | ASTM D955 | 1.59 mm |
Across Flow | *** % | ASTM D955 | 3.18 mm |
Across Flow | *** % | ISO 294-4 | 1.59 mm |
Across Flow | *** % | ISO 294-4 | 3.18 mm |
Viscosity | *** Pa-s | ASTM D 3835 | Melt Viscosity (190°C, 300 sec^-1) |
Abrasion resistance | *** mg/1000cy | ASTM D 1044 | 1.0E+6 g, CS-17 Wheel |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Strength | |||
Yield | *** Mpa | ASTM D 412 | 23°C |
Yield | *** Mpa | ISO 37 | 23°C |
at 100% strain | *** Mpa | ASTM D 412 | |
at 100% strain | *** Mpa | ISO 37 | 23°C |
Tensile Elongation | |||
Break | *** % | ASTM D 412 | |
Break | *** % | ISO 37 | 23°C |
Tear Strength | *** kN/m | ASTM D 624 | 24°C, Die C |
Compression Set | *** % | ASTM D 395 | 100°C, 22 hr |
Compression Set | *** % | ASTM D 395 | 24°C, 22 hr |
Compression Set | *** % | ASTM D 395 | 70°C, 22 hr |
Compression Set | *** % | ISO 815 | 100°C, 22 hr |
Compression Set | *** % | ISO 815 | 24°C, 22 hr |
Compression Set | *** % | ISO 815 | 70°C, 22 hr |
Tensile Set | *** % | ASTM D 412 | 100% Strain |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Brittleness Temperature | *** °C | ASTM D 746 | |
Brittleness Temperature | *** °C | ISO 812 | |
| Hardness | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Shore A hardness | *** A | ASTM D 2240 | 5 sec |
Shore A hardness | *** A | ISO 868 | 5 sec |
| Aging | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Strength(Heat Aging) | *** % | ISO 188 | Change in Air, 100°C, 168 hr |
Tensile Strength(Heat Aging) | *** % | ISO 188 | Change in Air, 70°C, 168 hr |
Tensile Strength(Heat Aging) | *** % | ASTM D573 | Change in Air, 100°C, 168 hr |
Tensile Strength(Heat Aging) | *** % | ASTM D573 | Change in Air, 70°C, 168 hr |
Elonggation(Heat Aging) | *** % | ASTM D573 | Change in Ultimate Elongation in Air, 100°C, 168 hr |
Elonggation(Heat Aging) | *** % | ASTM D573 | Change in Ultimate Elongation in Air, 70°C, 168 hr |
Change in Volume | *** % | ISO 1817 | 100°C, 168 hr, in ASTM #1 Oil |
Change in Volume | *** % | ISO 1817 | 100°C, 168 hr, in IRM 903 Oil |
Change in Volume | *** % | ISO 1817 | 100°C, 168 hr, in Wate |
Change in Volume | *** % | ISO 1817 | 24°C, 168 hr, in Reference Fuel B |
Change in Volume | *** % | ASTM D471 | 100°C, 168 hr, in ASTM #1 Oil |
Change in Volume | *** % | ASTM D471 | 100°C, 168 hr, in IRM 903 Oil |
Change in Volume | *** % | ASTM D471 | 100°C, 168 hr, in Wate |
Change in Volume | *** % | ASTM D471 | 24°C, 168 hr, in Reference Fuel B |
Tensile Modulus | *** % | ASTM D573 | Change in Air, 100°C, 168 hr |
Tensile Modulus | *** % | ASTM D573 | Change in Air, 70°C, 168 hr |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
