A glass fibre reinforced, flame retardant, partially aromatic polyamide for injection molding. Good mechanical properties, low water absorption, high melting point (295°C). High tracking resistance, low tendency to form deposits on electrical contacts,
| Original Document | Technical Datasheet(English) | |||
| Resin ID | PA6T/6-GF25 FR(52) | |||
| Availability | AsiaEuropeNorth AmericaMiddle EastAfricaSouth & Central America | |||
| Features | Flame RetardantFilled & Reinforced | |||
| Diagrams | Dynamic Shear modulus (G storage)-temperatureStress-strainStress-strain (Cond.)Secant modulus-strainSecant modulus-strain (Cond.)Stress-strain (isochronous)(Creep) 23°C (cond.)Stress-strain (isochronous)(Creep) 120°CCreep modulus-time 23°C (cond.)Creep modulus-time 120°CCoefficient of Linear Thermal Expansion(CTE)-TemperatureTensile modulus-temperatureTensile modulus-temperature (cond.) | |||
| Reinforced | 25% Glass Fiber | |||
| Physical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
|---|---|---|---|
Density/Specific Gravity | *** g/cm³ | ISO 1183 | |
Molding Shrinkage | |||
Flow | *** % | ISO 294-4 | parallel |
Across Flow | *** % | ISO 294-4 | |
constrained | *** % | - | |
Water Absorption | ***~*** cm³/g | ISO 62 | saturation in water at 23°C |
Water Absorption | ***~*** % | ISO 62 | equilibrium 23°C/50% r.h |
Viscosity | *** cm³/g | ISO 307, 1157, 1628 | 0.5% in 96 % H2SO4 |
| Mechanical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Tensile Modulus | *** Mpa | ISO 527-1/-2 | cond. |
Tensile Modulus | *** Mpa | ISO 527-1/-2 | dry |
Tensile Strength | |||
Break | *** Mpa | ISO 527-1/-2 | cond. |
Break | *** Mpa | ISO 527-1/-2 | dry |
Tensile Elongation | |||
Break | *** % | ISO 527-1/-2 | dry |
Tensile Creep Modulus | |||
1000h | *** Mpa | ISO 899-1 | cond. |
| Impact | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Charpy Notched Impact Strengh | |||
23℃ (73℉) | *** kJ/m² | ISO 179/1eA | dry |
Charpy Unnotched Impact Strengh | |||
23℃ (73℉) | *** kJ/m² | ISO 179/1eU | dry |
Izod Notched Impact Strengh | |||
23℃ (73℉) | *** kJ/m² | ISO 180/A | dry |
| Thermal | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Heat Deflection Temperature(HDT) | |||
1.8 Mpa (264 psi)(18.6kg/cm²) | *** °C | ISO 75-1/-2 | |
Specific Heat | *** J/kg-K | - | |
Coefficient of Linear Thermal Expansion | |||
Flow | *** E-6/K | ISO 11359-1/-2 | 23-80°C |
Across Flow | ***~*** E-6/K | ISO 11359-1/-2 | 23-80°C |
Melt Temperature(Tm) | *** % | ISO 11357-1/-3 | DSC |
Thermal Conductivity | *** W/(m K) | DIN 52612-1 | |
Temperature at Short Circle Operation | *** °C | - | |
Processing Temperature | ***~*** °C | - | |
Mould temperature | ***~*** °C | - | |
Temperature index (TI)-Tensile Strength | |||
5000 h | *** °C | IEC 60216 | |
20000 h | *** °C | IEC 60216 | |
| Flammability | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Flame Rating | |||
V-2 | *** mm | UL94 | NC |
V-0 | *** mm | UL94 | NC,BK |
V-0 | *** mm | UL94 | NC,BK,GY |
5VA | *** mm | UL94 | NC |
Oxygen Index | *** % | ISO 4589-1/-2 | |
Glow Wire Flammability Index(GWFI) | |||
0.75mm | *** °C | IEC 60695-2-12 | |
Glow Wire Ignition Test(GWIT) | |||
0.75mm | *** °C | IEC 60695-2-13 | |
| Electrical | Value/Unit(Sign in to View) | Test Standard | Test Condition |
Volume Resistivity | *** Ohm-m | IEC 60093 | cond |
Volume Resistivity | *** Ohm-m | IEC 60093 | dry |
Surface Resistivity | *** Ohm | IEC 60093 | cond |
Dielectric Constant(Permittivity) | |||
1MHz | *** - | IEC 60250 | dry |
Dissipation Factor | |||
1MHz | *** E-4 | IEC 60250 | dry |
Comparative Tracking Index (CTI) | |||
Solution A | *** V | IEC 60112 | |
Dielectric Strength | *** kV/mm | IEC 60243-1 | cond |
Dielectric Strength | *** kV/mm | IEC 60243-1 | dry |
The information presented on this datasheet was acquired by AjiEng.com from the producer of the material. AjiEng.com makes substantial efforts to assure the accuracy of this data. However, AjiEng.com assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.